Sign in Try it free

Flat and pitched roofs, facades The roof. Calculated.

Enter the geometry once, even from a PDF or DXF drawing. Tapered wedges, drainage, anchoring, pitched-roof covering and the facade panel layout all follow from it. Take-offs, the report and the site drawing on the phone come from the same model.

Try it free See what it does

  • No installation, runs in the browser
  • Based on Czech technical standards
  • Not tied to a single manufacturer
  • Data on our own servers in the Czech Republic
  • Access right after e-mail verification

One roof model

Draw the plan or trace it over a drawing once. The follow-up calculations take their dimensions from it, with no copying of values between spreadsheet and drawing.

Based on Czech standards

Drainage assessment to ČSN EN 12056-3 and ČSN 75 6760, with the verdict right on the roof. Fall protection is an indicative design based on TP 1.21: the output carries a watermark, the system supplier confirms it and it does not cover the structural assessment of the anchorage.

Report and take-offs

A print-ready report, material take-off and roof-covering bill of materials for ordering.

Three project types

Flat roof, pitched roof, facade. One tool.

You choose the type when you create the project. Each has its own calculations, drawing works the same in all of them and the outputs share one format.

Flat roof

Tapered insulation, drainage and anchoring for flat roofs

  • Tapered wedges A, B, C … with substrate boards and a take-off
  • Drainage and emergency drainage assessment with a verdict
  • Halls, diverters into valleys and around obstacles
  • Waterproofing with laps and upstands onto parapets, green roofs, thermal resistance
  • Membrane anchoring plan with anchor clamping lengths and an indicative fall-protection design from generic elements

Guides

ČSN EN 12056-3 · ČSN 75 6760 · TP 1.21

Pitched roof

Roof covering and batten take-offs for pitched roofs

  • Quick input, from a drawing or plane by plane, including dormers and a chimney across the ridge
  • Covering from manufacturer catalogues and a pitch check on every plane
  • Battens, sheet-metal piece drawings and metalwork parts counted in pieces
  • Documentation for roofers and metalworkers with a QR code

Guides

Climate zone K1–K3 · rafter length · 3D

Facade

Facade panel layout and cutting plan

  • Views and planes, building footprint and 3D
  • Panel layout with joints and a check of the minimum piece
  • Openings, including circular and angled ones, notched pieces
  • Cutting plan, piece drawing for the workshop and indicative substructure axes

Guides

No structural design, fixing or anchorage to the structure.

Try it

Try tapered insulation on a simple roof

Enter a rectangle or an L, the drains and the slope. The calculator computes the tapered insulation volume and the flow to each drain with the same core as FredIQ. No registration.

Indicative calculation. Your own plan from a drawing, the piece-by-piece wedge take-off and the report are in FredIQ. Open the calculator on its own page

Workflow

From drawing to report

Four steps in one tool. No values are copied between them by hand.

  1. Input

    Enter the roof

    Upload a drawing as a PDF, image or DXF, set the scale and trace the outline, drains and openings. For a pitched roof, quick input is enough: rectangle or L, shape and pitch.

    PDF · PNG · JPG · DXF · scale

  2. Model

    The app derives the planes

    For a flat roof, slope planes, ridges and valleys from the outline and the drains you place. For a pitched roof, planes, ridge, hips and valleys from shape and pitch.

    planes · ridges · valleys · hips

  3. Calculations

    Calculate the solution

    Tapered wedges, drainage assessment, anchoring plan and fall protection. For a pitched roof, covering assessment, take-off and flashings; for a facade, panel layout and cutting plan.

    ČSN EN 12056-3 · ČSN 75 6760 · TP 1.21

  4. Output

    Hand over the documents

    Report, documents for suppliers, take-offs and the site drawing. No prices.

    report · supplier documents · take-offs · CSV

One model

One roof model, linked calculations

Slopes, drainage, anchoring, fall protection and covering all read the same geometry. No dimensions are copied between programs.

Changed the geometry? The outputs derived from it are invalidated and you generate them again. Nothing stays silently complete on an outdated basis.

Flat roof

  • Slope wedges

    Wedges and a take-off with types A, B, C … by height band, in one click.

  • Drainage

    Standard assessment (Q = r·A·C): required drain count and a pass/fail verdict.

  • Envelope anchoring plan

    Empirical membrane anchoring: layout and anchor lengths by zone.

  • Fall protection

    An indicative design from generic elements: anchor points, lines, coverage and risk zones. The output carries a watermark and the system supplier confirms it before installation.

  • Green roof

    Layer quantities, gravel border and fire rules on top of the finished tapering.

  • Halls and diverters

    Sloped deck, drainage skeleton and diverters into valleys or envelope patterns.

Pitched roof

  • Covering and pitch check

    Shape from quick input or a drawing, covering from manufacturer catalogues and a pitch check on every plane.

  • Flashings and bill of materials

    Lengths of eave, verge, ridge, hips and valleys along the roof surface, and a CSV bill of materials for ordering.

Facade

  • Panel layout

    Panels with joints across views and planes, around openings and with a check of the minimum piece.

  • Cutting plan

    Panel cutting, a piece drawing for the workshop and indicative substructure axes, without structural design or fixing.

Shared

  • Materials and assemblies

    Assembly from the catalogue, roll consumption with laps and waste, and an indicative thermal resistance of the flat roof.

  • Manufacturer catalogues

    Membranes, coverings, drains and facade panels from manufacturer data, including roll widths and cover dimensions.

Roof covering in detail

Roof covering is more than an area in square metres

Tiles are counted row by row from the layout of each roof plane. Batten spacing follows from the pitch and the specific tile, a cut tile is ordered whole, and flashings are measured along the roof surface.

  • Batten spacing from the manufacturer’s range for the given pitch. The eave batten takes up the remainder, so no trimmed row is left under the ridge.
  • Whole and cut pieces from the plane layout, not from a bounding rectangle. A cut tile is ordered whole.
  • Verge tiles and half tiles as separate items of the take-off.
  • Flashings as lengths along the roof surface: eave, verge, ridge, hip, valley and flashings around openings.
  • Waste is shown next to the net counts, not hidden inside them.
  • After the roof shape changes, the layout and the take-off are recalculated.

Manufacturer catalogues

A product is more than a catalogue entry

Every product carries technical values from the manufacturer’s documents and the rules the app uses to calculate with it.

Pitched roof

Covering pitch

Minimum and safe pitch from the manufacturer. Between the two, the covering is suitable only with a condition: an underlay of a higher watertightness class.

Rule pitch below safe pitch → suitable with a condition

Pitched roof

Battens

Batten spacing range by pitch, eave batten and ridge batten from the documents for the specific tile.

Rule rafter length = eave batten + n × spacing + ridge batten

Pitched roof

Metal sheets

A strip longer than the maximum sheet is split with a lap along the slope, and the cross joint has its own minimum pitch. Standing seam roofs count fixed and sliding clips.

Rule strip length > max. sheet → cross joint with lap

Flat roof

Waterproofing membranes

Roll width and length, waste and laps as a percentage according to material, attachment and roll size, upstands onto parapets and walls. The number of rolls follows from the full roll area.

Rule rolls = (area × (1 + waste and laps) + upstand × (1 + upstand waste and laps)) ÷ (width × length), rounded up

Flat roof

Fasteners

At each fastener the build-up thickness is added up and grouped by a chosen step. From that the fastener manufacturer determines the lengths.

Rule thickness = insulation + tapered wedge + other layers at the fastener

Flat roof

Drains and overflows

The catalogue capacity of a drain is compared with the required flow. For emergency drainage the app suggests the smallest catalogue overflow that is enough.

Rule Σ overflow capacity ≥ emergency flow

Facade

Facade panels

Format, joint and minimum piece from the manufacturer data. The app removes a piece that is too small by shifting the grid or merging it with its neighbour, and warns about it where that is not possible.

Rule piece < minimum piece → grid shift or merge, otherwise a warning

Technical values of roof coverings cite the manufacturer’s document. When one changes, the saved covering take-off is marked invalid until you confirm the change.

Manufacturer catalogues in FredIQ

Manufacturers whose products are in the app catalogue and feed into the calculations. Listed in alphabetical order; not a recommendation or a rating.

Flat roof waterproofing

  • Bauder
  • BITUMAX
  • BMI střešní a hydroizolační systémy s.r.o.
  • Fatra
  • Protan
  • Sika
  • SOPREMA

Roof drainage

  • b/s/t
  • Grumbach
  • HL Hutterer & Lechner
  • Sita Bauelemente
  • SP Profil

Green roofs

  • Optigruen

Roof tiles

  • BETONPRES
  • BMI Bramac
  • KM BETA
  • TONDACH

Metal roofing

  • EVROmat
  • ROVA
  • Ruukki
  • SATJAM
  • STŘECHY COMAX

Fibre cement roofing

  • Swisspearl (dříve Cembrit)

Facade panels

  • Swisspearl

Product data in the catalogue comes from the manufacturers’ documentation.

Outputs and the site

The calculation does not end with a number on screen

The outputs are built from the same data the app calculates with. You release the report and the supplier documents as revisions with their own numbering and a checksum.

Full project report

A report for one roof or for the whole project, with a summary page and a consolidated bill of materials.

Documents for suppliers

A document for each trade: insulation and tapered wedges, anchoring, fall protection system, green roof, roofers and metalworkers, facade panel installation and cutting. No prices and no client contact details.

Take-offs

Material take-off by material, by roof or as a total, in PDF and CSV.

DXF export

The slope, wedge and drain plan of a flat roof as a DXF drawing. If FredIQ knows your original drawing, it lands exactly on it; otherwise you get a separate drawing in millimetres.

The site drawing on a phone

The QR code in a released document opens the drawing on a phone, without signing in and in six languages. A tap shows the details of a wedge, anchor, plane or panel. It is always the released revision, never work in progress.

Guides

Collaboration

Work with your colleagues and with manufacturers

Company and colleagues

Invite colleagues to your company by e-mail. You then see and edit the company’s projects together, and the project list switches between your own projects and those of the whole company.

Manufacturer network

A materials manufacturer invites companies to its network. A company joins only with its consent and adds only the projects it chooses. For those the manufacturer sees the materials and the bill of materials, never the client’s contact details.

Fred and Help

Ask Fred, find the guides in Help

Fred, the in-app assistant

Ask right on the screen you are working on. Fred knows the state of the open project and answers from texts approved by a technical expert. It does not replace professional assessment.

Illustrated guides

Step-by-step instructions with screenshots, in six languages. Available without signing in. The app, the reports and the site drawing speak six languages. Open Help

Questions and answers

Frequently asked questions about FredIQ

Does FredIQ calculate tapered insulation with a take-off?

Yes. From the plan, the drains and the slope it designs the tapered wedges with ridges and valleys, draws the laying plan and produces a take-off of wedges and substrate boards for ordering. It also handles halls with diverters into valleys and around obstacles.

Does FredIQ calculate to Czech standards?

Yes, wherever a calculation relies on a standard: drainage is assessed to ČSN EN 12056-3 and ČSN 75 6760, the minimum slope is checked to ČSN 73 1901 and fall protection is an indicative design based on TP 1.21. FredIQ does not calculate to the standards of other countries.

What does FredIQ not assess?

It does not assess the structure of the roof or the rafters, wind uplift, the load capacity of membrane fasteners and anchor points, or the fire safety of the building. The outputs are a technical basis for ordering and installation and require a professional check. Full overview in Help

Is FredIQ tied to a single manufacturer?

No. The catalogues contain membranes, drains, roof coverings and other materials from several manufacturers, and the calculations use their technical data. You choose which material to use.

Which languages does FredIQ support?

The app, the reports, the site drawing and the guides in Help are available in Czech, English, German, Polish, Spanish and French.

Where is the data stored?

On the operator’s own servers in the Czech Republic. Further details are in the privacy policy.

Runs in the browser

Stop recalculating the roof by hand.

Free registration. Draw the roof and within minutes you have the follow-up calculations and the material take-off.

Register free Got a question? Write to us

No card · Access right after e-mail verification · 14 days of FredIQ Complete free · Operated by DRAJON spol. s r.o.